Product ID:SCOTCHWELD 1469 EPOXY ADHESIVE
MSDS Date:01/01/1987
FSC:8040
NIIN:00-932-1945
MSDS Number: BFXGN

Emergency Phone: 612-733-1110 OP 55

Cage: 76381

Telephone: 866-556 5712 / 612-733-1110

Cage: 76381

DICYANDIAMIDE, AL POWDER, SYN RUBBER,AMORPHOUS SILICA

EPOXY RESIN BLEND, DILUENT, POLYGLYCOL DIEPOXIDERESIN BLEND

150-68-5)(2-4%)

CAS: 150-68-5

RTECS: YS6300000

Effects of Overexposure:EYE,SKN: IRRT,POSS SENSITIZATION.INH:NONE
EXPECTED @ ROOM TEMP. SENS/IRRT FROM CURING VAPORS OR DUST

First Aid:EYE: FLUSH 10 MIN W/COPIOUS WATER. SKN: WASH W/SOAP & WATER.
LAUNDER CONTAM CLOTHING BEFORE REUSE. INGES, INHL:NO ACTION
INDICATED.

Flash Point:>200F/93C (CC)
Extinguishing Media:CO/2,FOAM, DRY CHEMICAL
Fire Fighting Procedures:USE SCBA WHEN FIGHTING FIRES INVOLVING THIS
MATERIAL.
Unusual Fire/Explosion Hazard:NONE

Spill Release Procedures:OBSERVE ALL LISTED PRECAUTIONS. COLLECT
SPILLAGE, CLEANUP RESIDUE, STORE/SHIP IN APPROVED CONTAINERS ONLY.
USE ABSORBENTS AS NEEDED.

Handling and Storage Precautions:AVOID EYE & SKN CONTACT. AVOID INHL &
EYE CONTACT WITH DUST & PARTICULATES FROM GRINDING OR SAWING OF
CURED PRODUCT.
Other Precautions:3-(P-CHLOROPHENYL)-1-1 DIMETHYL UREA IS SUSPECT
CARCINOGEN. NO EXPOSURE EXPECTED IN NORMAL USE

Respiratory Protection:USE DUST MASK DURING GRINDING/CUTTING CURED
RESIN.AVOID INHL CUR VAP
Ventilation:EXHAUST ALL CURING OVENS TO OUTDOORS
Protective Gloves:IMPERVIOUS
Eye Protection:SAFETY GLASSES
Other Protective Equipment:USE DUST MASK WHEN GRINDING CURED PRODUCT
Supplemental Safety and Health
UPDATE PER 3M MSDS(OSHA) 1NOV85,DOC# 1031236. 3M GENERIC
ID#:62-1469-XXXX-X.FORMER P/N:SCOTCHWELD EC-1469 STRUCTURAL
ADHESIVE.MFR STATES PRODUCT NOT A KIT.KEY1:N1.

HCC:N1
Spec Gravity:1.2
Solubility in Water:NIL
Appearance and Odor:VISCOUS CREAM COLORED LIQUID W/LOW ODOR
Percent Volatiles by Volume:0

Stability Indicator/Materials to Avoid:NO
Stability Condition to Avoid:PROLONGED STORAGE AT ELEVATED TEMP.
Hazardous Decomposition Products:CO,CO*2,N,HCN POSSIBLE WHEN EXP TO
EXCESSIVE HEAT/FLAME.
Conditions to Avoid Polymerization:ELEVATED STORAGE TEMP.

Waste Disposal Methods:COMMERCIAL INCINERATION AT 99.99% EFF OR
RECLAMATION IS PREFERRED. LANDFILL OR OTHER DISPOSAL IAW
LOC/STATE/FED REGS ONLY

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.